Important Plumbing Tips for Installing a Bathtub
Important Plumbing Tips for Installing a Bathtub
Blog Article
We have unearthed this post involving A Step-by-Step Guide to Installing a Bathtub directly below on the web and felt it made perfect sense to share it with you on my blog.
Mounting a bathtub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub and embeded in the brand-new one. Make certain you have actually qualified yourself for the job as well as fit trying it. As opposed to hiring a professional to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This article will certainly assist you set up a brand-new tub in your restroom if you have already purchased a new tub and don't need to change the setup of your previous water system pipelines.
Your tools and material list must comprise the following:
Planning for the Installation
To start with, the supporting framework supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome as a result of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, position the bathtub in the called for setting. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub up until the level checks out level.
To install faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been utilized a minimum of once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making certain that the washers are in location between the faucet and also the sink. Safeguard the faucet in position with the manufacturer given backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind ought to be attached to the faucet ends initially, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, causing the water to pass through the wall between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to securing, to enable the activity experienced when the bathtub remains in use. The sealant can crack relatively early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on How to Install a Bathtub from someone on our other blog. Sharing is good. Helping people is fun. Thank you for taking the time to read it.
Book-Now Report this page